>
> Hi Andrew:
> I have not tried the different types of coil connections that you are
> proposing. But as we are not dealing with the usual EM energies when
> pyramids are brought into the picture all I can suggest is to pendulum
> and energy test each configuration to see which one gives you the
> strongest positive response.
> Myself when projecting positive healing energy from A to B using bare
> coiled copper wire (carrying zero current) the strongest result is
> with the wire wrapped around a cardboard roll in a helical pattern and
> running clockwise from bottom to top. Running the copper wire
> counterclockwise from bottom to top was much more effective for
> removing negative energies from the target person.
> Again Andrew that's only my experience - I cannot be more specific
> since I believe you have to experiment to see what works for you.
> Thanks for the idea of the infinity loop - this is similar to the
> Mobius pattern and some reports indicate it is quite effective in
> attracting some forms of free energy.
> Regarding soldering I try to stay away from lead based solder for a
> number of reasons. Lead free solder while a little more difficult to
> work with is available.
> Ray
> ----- Original Message -----
> From: Andrew McAfee
> To: [hidden email]
> Sent: Sunday, February 20, 2005 11:23 AM
> Subject: [eSens] wire twisting
>
>
> Ray,
> I enjoyed hearing about the EM fields with the wiring. I am playing
> with copper wire and shaping them circles; circumferences relative to
> the Earth and in the diameter and base of the Great Pyramid.
> My understanding is if I were to use only one wire in a circle,
> there
> is a positive side and an negative side. In order to create a
> positive
> energy flow through the circle I am twisting two wires together so
> the
> resultant twist is in a clockwise direction. Would you agree that
> this
> would create a positive energy flow and field vs. detrimental effect?
> Another question I have is when I bring the two wires together in
> forming a circle, I intend to solder them in such a way that the
> positive end of one wire is not only connected to the negative end of
> its own wire but to both its own wire and the other wire that it is
> twisted with. I think this will cancel the positive-negative and
> create
> only a beneficial field.
> Or, will it be more effective if I create an infinity loop with the
> two
> wires where the first wire is only soldered to second wire and not to
> itself? Should I solder the the positive end of wire one to the
> positive end of the second wire?
> Andrew
> On Feb 20, 2005, at 8:14 AM, Ray Kosan wrote:
>
>>
>> Hi Yildiz:
>>
>> Rolling up any cord carrying alternating current (AC) will increase
>> the strength of the electric and magnetic fields in the vicinity of
>> the roll. The main reason for this is that the fields are reinforced
>> by each roll since the current flow is in the same direction in
>> adjacent wires in the roll.
>> Also probably not a good idea to have sensitive electronic equipment
>> close to such rolls because of the effect of the radiated EMF
>> interference from such rolls on the electronics.
>> Best bet is to get a cord of the right length but if you must roll it
>> up keep the roll as far away from yourself as possible.
>> If there is enough floor space and not too much extra cord then a
>> zigzag pattern will have the effect of current flowing in the opposite
>> direction in adjacent zigzags so that their EM fields are neutralized
>> rather than reinforced. Roughly this is the way the EM field is
>> neutralized at the main feeder line where the electric power is
>> connected to and enters at the side of a house. When this is done much
>> lower levels of EM radiation are measured inside the house close to
>> the electric meter.
>> Ray
>> ----- Original Message -----
>> From: Yildiz
>> To: [hidden email]
>> Sent: Sunday, February 20, 2005 5:50 AM
>> Subject: [eSens] question about long extension cord
>>
>>
>> Hi all,
>>
>> I need to use an extension cord for some of my appliances.I have an
>> extension cord which is quite longer than I need. I am worried of that
>> longer cord might generate more EMF than the shorter one.I am thinking
>> of using it by rolling the cord thightly at some part of it to shorten
>> it. If we roll the cord to shorten it shall we still have high EMF? Or
>> should I buy a shorter cord to minimize EMF that will be generated.
>> Thanks in advance.
>> Best wishes.
>> Nil
>>
>>
>> [Non-text portions of this message have been removed]
>>
>>
>> Yahoo! Groups Sponsor
>>
>> Get unlimited calls to
>>
>> U.S./Canada
>>
>>
>>
>>
>> ----------------------------------------------------------------------
>> -
>> -------
>> Yahoo! Groups Links
>>
>> a.. To visit your group on the web, go to:
>> http://groups.yahoo.com/group/eSens/
>>
>> b.. To unsubscribe from this group, send an email to:
>> [hidden email]
>>
>> c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of
>> Service.
>>
>>
>>
>> [Non-text portions of this message have been removed]
>>
>>
>>
>>
>>
>> Yahoo! Groups Links
>>
>>
>>
>>
>>
>>
>>
>
>
> Yahoo! Groups Sponsor
>
> Get unlimited calls to
>
> U.S./Canada
>
>
>
>
> -----------------------------------------------------------------------
> -------
> Yahoo! Groups Links
>
> a.. To visit your group on the web, go to:
> http://groups.yahoo.com/group/eSens/
>
> b.. To unsubscribe from this group, send an email to:
> [hidden email]
>
> c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of
> Service.
>
>
>
> [Non-text portions of this message have been removed]
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>