about the Electrosmog Dectecter

Marc asked for info about the new Electrosmog Detecter. First here
are some excerpts from the Web site about the product:

* The designer of the Detector, Alasdair Philips, was a key witness in the
evidential process which culminated in the 'Mobile Phones and Health Report'
(Stewart Report) 2000, updated 2004.

* The Electrosmog Detector enables you to 'hear' the electrosmog that
exists all around you. It is not an alarm, nor is it a warning device. It is an
educational tool providing an awareness of your personal environment.

* The level and quality of the noise the Electrosmog Detector emits is
directly related to the changes in levels of man-made microwave radiation.

* The Electrosmog Detector is a modern, carefully designed, pulsing
microwave radiation detector. Unlike anything else on the market at present, it
detects and sums the totality of the incoming microwave radiation amplitude
modulation, above about 30 millivolts per metre strength, allowing you to hear the
result. It is both accurate and credible.

* The Electrosmog Detector is the first true consumer product in this
category.

Technical specifications:

Frequency Range: 50 MHz to 3000 MHz
Sensitivity: 0.01 volts per metre (V/m)
Output: Audio Loudspeaker, Audio jack socket
Controls: On/Off Switch, Volume

Credentials: Patented and fully tested to
traceable international standards.

Dimensions: 147 x 85mm
Weight: 170gms (inc. 9V battery - supplied)

(They also sell shielding fabrics.)  
Our fabrics deflect in excess of 90% of Electrosmog across the spectrum of
wireless communications emissions (Fig 1.3).

Two stylish and light-weight fabrics are currently available for purchase by
the metre. These are similar in construction to fine gauze.

* Swiss Shield® "Evolution" fine woven white polyester - highly
effective yet aesthetically pleasing fabric suitable for curtains and linings.


* Swiss Shield® "Proto-D" net-knit polyester, highly effective as net
curtains or linings.

You can download a data sheet for these products.
(end of excerpts from their website.)

You can see the Electrosmog Dectecter, read about it and even hear clips
of the sounds it emits when exposed to various wireless broadcasts, at
www.sensoryperspective.com /.

In my experience with it so far, I have heard sounds a lot more dramatic
than those recorded on the Web site. And it is very interesting to
actually be able to hear the different frequencies, the pulsing, etcetera.
Really old cordless phones (analog, I suppose) are not too bad, but the
new ones are absolutely horrible. The Detecter makes a horrid sound even
in the next room away from the phone base. This is with the handset not even
on. 24 hrs.a day. Then when you click the "on" button on the handset, a
totally different much higher pitched whine chimes in as well.
Some radio and MW towers I drive by do not radiate much that hits the
car, but a shorter tower next to the police station in a small town nearby is
the worst thing I have heard yet. LOUD blasting pulses. I am trying to
think of some way to go there and clue them in. My husband, however, warns me
that doing that at a police station could result in my being held for some time
for questioning. I'll let you know if that happens!

Following are some remarks regarding the Dectector, from my
correspondence with Ian.

The detector captures the gross amount of emissions (electrosmog) in the
range 50 Mhz to 3 Ghz - this means that if there is more than once source in the
vicinity it will sum the outputs and provide an audio signal commensurate with
the total.
 
The Detector covers all current and planned wireless communications devices
includiing GSM, 3G/UMTS and TETRA. It will also respond to radio phones,
walkie-talkies, wireless burglar alarms, wireless baby alarms and microwaveovens.
 
We are not aware of any broad market wireless products that it will not
detect and it should respond to all cell phone transmitters in your vicinity.

studies which indicate that 0.01 V/m is the starting point of health effects.
That is why our Detector starts to activate at exactly that point. If you can
detect noise on it there is reason to take notice. If you get a lot of noise,
especially where you spend a lot of time and particularly in bedrooms then
you need to do something about it.

The device will help them identify "hotspots" and to creat "quiet zones" but
if they need absolute zero they need more specialist equipment and other
technical support.

The important point to raise is that with a zero landscape detector, there
are practically no quiet zones - the detector would never be "silent"and soit
would be difficult for the general public to establish the differntial between
hotspots and quiet zones - and it is the differential that is the important
factor.
 
For most people, minor lifestyle adjustments can lead to dramtic reductions
in exposure - that is the message we are aiming to get across. Zero landscape
is a battle that can't be won...not in the world we live in.

(end of Ian's comments)

As I said, I am becoming a distributor. I'm starting by taking orders
for an initial shipment to be sent in early November, so if you want an
Electrosmog Dectecter, please get in touch with me directly. In the US, the
Detecters will sell for $89 plus some tax and shipping.
Regards,
Shivani
     


[Non-text portions of this message have been removed]

Hello Shivani,

contrary to what they claim, the Electrosmog Detector starts only above 0.05
V/m.

I tested it under phone masts, and was disappointed with the sounds.
I regard it a nice gadget, but unsuitable for electrosensitive people.


Greetings,
Charles Claessens
member Verband Baubiologie
www.milieuziektes.nl
www.milieuziektes.be
www.hetbitje.nl
checked by Norton Antivirus



----- Original Message -----
From: <[hidden email]>
To: <[hidden email]>
Sent: Tuesday, October 11, 2005 04:02
Subject: [eSens] about the Electrosmog Dectecter


> Marc asked for info about the new Electrosmog Detecter. First here
> are some excerpts from the Web site about the product:
>
> * The designer of the Detector, Alasdair Philips, was a key witness in the
> evidential process which culminated in the 'Mobile Phones and Health
Report'
> (Stewart Report) 2000, updated 2004.
>
> * The Electrosmog Detector enables you to 'hear' the electrosmog that
> exists all around you. It is not an alarm, nor is it a warning device. It
is an
> educational tool providing an awareness of your personal environment.
>
> * The level and quality of the noise the Electrosmog Detector emits
is
> directly related to the changes in levels of man-made microwave radiation.
>
> * The Electrosmog Detector is a modern, carefully designed, pulsing
> microwave radiation detector. Unlike anything else on the market at
present, it
> detects and sums the totality of the incoming microwave radiation
amplitude
> modulation, above about 30 millivolts per metre strength, allowing you to
hear the by
> the metre. These are similar in construction to fine gauze.
>
> * Swiss Shield® "Evolution" fine woven white polyester - highly
> effective yet aesthetically pleasing fabric suitable for curtains and
linings.
>
>
> * Swiss Shield® "Proto-D" net-knit polyester, highly effective as net
> curtains or linings.
>
> You can download a data sheet for these products.
> (end of excerpts from their website.)
>
> You can see the Electrosmog Dectecter, read about it and even hear
clips
> of the sounds it emits when exposed to various wireless broadcasts, at
> www.sensoryperspective.com /.
>
> In my experience with it so far, I have heard sounds a lot more
dramatic
> than those recorded on the Web site. And it is very interesting to
> actually be able to hear the different frequencies, the pulsing, etcetera.
> Really old cordless phones (analog, I suppose) are not too bad, but
the
> new ones are absolutely horrible. The Detecter makes a horrid sound
even
> in the next room away from the phone base. This is with the handset not
even
> on. 24 hrs.a day. Then when you click the "on" button on the handset,
a
> totally different much higher pitched whine chimes in as well.
> Some radio and MW towers I drive by do not radiate much that hits the
> car, but a shorter tower next to the police station in a small town nearby
is
> the worst thing I have heard yet. LOUD blasting pulses. I am trying
to
> think of some way to go there and clue them in. My husband, however,
warns me
> that doing that at a police station could result in my being held for some
time
> for questioning. I'll let you know if that happens!
>
> Following are some remarks regarding the Dectector, from my
> correspondence with Ian.
>
> The detector captures the gross amount of emissions (electrosmog) in the
> range 50 Mhz to 3 Ghz - this means that if there is more than once source
in the
> vicinity it will sum the outputs and provide an audio signal commensurate
with
> the total.
>
> The Detector covers all current and planned wireless communications
devices
> includiing GSM, 3G/UMTS and TETRA. It will also respond to radio phones,
> walkie-talkies, wireless burglar alarms, wireless baby alarms and
microwave ovens.
>
> We are not aware of any broad market wireless products that it will not
> detect and it should respond to all cell phone transmitters in your
vicinity.
>
> studies which indicate that 0.01 V/m is the starting point of health
effects.
> That is why our Detector starts to activate at exactly that point. If you
can
> detect noise on it there is reason to take notice. If you get a lot of
noise,
> especially where you spend a lot of time and particularly in bedrooms then
> you need to do something about it.
>
> The device will help them identify "hotspots" and to creat "quiet zones"
but
> if they need absolute zero they need more specialist equipment and other
> technical support.
>
> The important point to raise is that with a zero landscape detector, there
> are practically no quiet zones - the detector would never be "silent"and
so it
> would be difficult for the general public to establish the differntial
between
> hotspots and quiet zones - and it is the differential that is the
important
> factor.
>
> For most people, minor lifestyle adjustments can lead to dramtic
reductions
> in exposure - that is the message we are aiming to get across. Zero
landscape
> is a battle that can't be won...not in the world we live in.
>
> (end of Ian's comments)
>
> As I said, I am becoming a distributor. I'm starting by taking
orders
> for an initial shipment to be sent in early November, so if you want an
> Electrosmog Dectecter, please get in touch with me directly. In the US,
the
> Detecters will sell for $89 plus some tax and shipping.
> Regards,
> Shivani
>

Would the short tower next to the police station be a Tetra mast? I have heard reports that this is the new network used by UK police and is particularly bad on emissions.
----- Original Message -----
From: [hidden email]
To: [hidden email]
Sent: Tuesday, October 11, 2005 3:02 AM
Subject: [eSens] about the Electrosmog Dectecter


Marc asked for info about the new Electrosmog Detecter. First here
are some excerpts from the Web site about the product:

* The designer of the Detector, Alasdair Philips, was a key witness in the
evidential process which culminated in the 'Mobile Phones and Health Report'
(Stewart Report) 2000, updated 2004.

* The Electrosmog Detector enables you to 'hear' the electrosmog that
exists all around you. It is not an alarm, nor is it a warning device. Itis an
educational tool providing an awareness of your personal environment.

* The level and quality of the noise the Electrosmog Detector emits is
directly related to the changes in levels of man-made microwave radiation.

* The Electrosmog Detector is a modern, carefully designed, pulsing
microwave radiation detector. Unlike anything else on the market at present, it
detects and sums the totality of the incoming microwave radiation amplitude
modulation, above about 30 millivolts per metre strength, allowing you tohear the
result. It is both accurate and credible.

* The Electrosmog Detector is the first true consumer product in this
category.

Technical specifications:

Frequency Range: 50 MHz to 3000 MHz
Sensitivity: 0.01 volts per metre (V/m)
Output: Audio Loudspeaker, Audio jack socket
Controls: On/Off Switch, Volume

Credentials: Patented and fully tested to
traceable international standards.

Dimensions: 147 x 85mm
Weight: 170gms (inc. 9V battery - supplied)

(They also sell shielding fabrics.)  
Our fabrics deflect in excess of 90% of Electrosmog across the spectrum of
wireless communications emissions (Fig 1.3).

Two stylish and light-weight fabrics are currently available for purchaseby
the metre. These are similar in construction to fine gauze.

* Swiss Shield® "Evolution" fine woven white polyester - highly
effective yet aesthetically pleasing fabric suitable for curtains and linings.


* Swiss Shield® "Proto-D" net-knit polyester, highly effective as net
curtains or linings.

You can download a data sheet for these products.
(end of excerpts from their website.)

You can see the Electrosmog Dectecter, read about it and even hear clips
of the sounds it emits when exposed to various wireless broadcasts, at
www.sensoryperspective.com /.

In my experience with it so far, I have heard sounds a lot more dramatic
than those recorded on the Web site. And it is very interesting to
actually be able to hear the different frequencies, the pulsing, etcetera.
Really old cordless phones (analog, I suppose) are not too bad, but the
new ones are absolutely horrible. The Detecter makes a horrid sound even
in the next room away from the phone base. This is with the handset not even
on. 24 hrs.a day. Then when you click the "on" button on the handset, a
totally different much higher pitched whine chimes in as well.
Some radio and MW towers I drive by do not radiate much that hits the
car, but a shorter tower next to the police station in a small town nearby is
the worst thing I have heard yet. LOUD blasting pulses. I am tryingto
think of some way to go there and clue them in. My husband, however, warns me
that doing that at a police station could result in my being held for some time
for questioning. I'll let you know if that happens!

Following are some remarks regarding the Dectector, from my
correspondence with Ian.

The detector captures the gross amount of emissions (electrosmog) in the
range 50 Mhz to 3 Ghz - this means that if there is more than once sourcein the
vicinity it will sum the outputs and provide an audio signal commensuratewith
the total.

The Detector covers all current and planned wireless communications devices
includiing GSM, 3G/UMTS and TETRA. It will also respond to radio phones,
walkie-talkies, wireless burglar alarms, wireless baby alarms and microwave ovens.

We are not aware of any broad market wireless products that it will not
detect and it should respond to all cell phone transmitters in your vicinity.

studies which indicate that 0.01 V/m is the starting point of health effects.
That is why our Detector starts to activate at exactly that point. If youcan
detect noise on it there is reason to take notice. If you get a lot of noise,
especially where you spend a lot of time and particularly in bedrooms then
you need to do something about it.

The device will help them identify "hotspots" and to creat "quiet zones" but
if they need absolute zero they need more specialist equipment and other
technical support.

The important point to raise is that with a zero landscape detector, there
are practically no quiet zones - the detector would never be "silent"and so it
would be difficult for the general public to establish the differntial between
hotspots and quiet zones - and it is the differential that is the important
factor.

For most people, minor lifestyle adjustments can lead to dramtic reductions
in exposure - that is the message we are aiming to get across. Zero landscape
is a battle that can't be won...not in the world we live in.

(end of Ian's comments)

As I said, I am becoming a distributor. I'm starting by taking orders
for an initial shipment to be sent in early November, so if you want an
Electrosmog Dectecter, please get in touch with me directly. In the US, the
Detecters will sell for $89 plus some tax and shipping.
Regards,
Shivani
       


[Non-text portions of this message have been removed]



------------------------------------------------------------------------------
YAHOO! GROUPS LINKS

a.. Visit your group "eSens" on the web.
     
b.. To unsubscribe from this group, send an email to:
[hidden email]
     
c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


------------------------------------------------------------------------------




[Non-text portions of this message have been removed]